Restore your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a simple process that can be performed in just a few procedures.

• First ensuring your red dot sight is turned on.
• Find the small button for reset on the side of the device.
• Utilize a small object to depress the reset switch for approximately three moments.
• Disengage the reset button and your Holosun EPS Carry Red Dot sight will reboot.
• Its red dot sight should now be returned to its factory settings.

Reset Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it to its factory configuration is a breeze. First, find the tiny button on the rear of your optic. Then, keep pressed it for around ten seconds until you see a brief flash. Your Holosun EPS Carry is now returned to its factory settings, ready for precise aiming.

Bring Your Holosun EPS Carry Back to Action

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. website Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

• Simultaneously press and hold the power button for approximately 10 seconds.
• An indicator will flash, indicating that the reset is being performed.
• Release the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and verify your sight's functionality. If you encounter any further troubles, don't hesitate to seek help from Holosun's support.

Restore Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

• First, Activate your Holosun EPS Carry by pressing the power button.
• Next, press and hold both the mode button and the up/down adjustment button simultaneously.
• As you continue holding these buttons, press the power button once.
• The display will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically deactivate.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Original reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Manual for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Restore your Holosun EPS Carry through a Factory Default Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the fix. This will restore your sight to its initial settings, clearing any altered configurations you've made. To accomplish this reset, follow these simple steps:

• First, locate the reset button on your EPS Carry.
• Then, engage a thin object, like a pen tip, to push the reset switch.
• During keep the reset button engaged, power on your EPS Carry.
• The sight will blink a message indicating that the reset is finished.

When the reset is finished, your EPS Carry will be set to its factory settings.

Report this wiki page